With the #Tsurumi guide rail systems, our pumps can be easily connected, moved up and down and removed again. Each system consists of rails or channels that connect the pump to the pipework. When the pump is lowered or raised, it slides along the rails - connected to an outlet pipe.
The guide rail systems simplify maintenance and reduce the risk of extended downtime. Unlike fixed pipework systems, which can take several hours to install and assemble, a pump on a guide rail is ready for operation more quickly.
Guide rail systems are particularly important in wet wells or sumps. For lifts deeper than four and a half metres, we recommend using a direct guide rail mount for added stability and smoother pump removal. Material selection is an important factor when choosing a guide rail system. Depending on the type of liquid being pumped, the rails can be made of stainless steel, cast iron or high-density polyethylene.
We are happy to answer your questions about the different types of our guide rails. Simply write to us: sales@tsurumi.eu
#Tsurumi
In the Gorges du Verdon, one of France's most famous gorges, an ambitious construction project is currently underway: a 250-metre bypass is being built to secure a tunnel. Before excavation could even begin, a major challenge had to be overcome — the diversion of an impressive 180,000 cubic metres of water.
The team from Tsurumi France took on this demanding task with precision and determination. Over the course of a week, the team prepared the site by lowering three series of Tsurumi pumps 22 metres below ground level, installing pipes for horizontal water drainage (with a 21-metre height difference), setting up settling basins, and completing all electrical connections.
On Tuesday, 3 September, at 8:30 a.m., the pumps were started:
One GSZ, two KRD and three LH models, each designed for extreme operating conditions, worked continuously and reliably until Thursday, 5 September, at 1:30 a.m. By that time, 90,000 cubic metres of water had already been successfully pumped out — the remainder drained away naturally by gravity.
This impressive operation once again demonstrates the reliability, strength and endurance of Tsurumi pumps – even under the toughest environmental conditions.
Would you like to learn more about our high-performance pumps, made in Japan?
Contact us at sales@tsurumi.eu
#Tsurumi #WaterManagement #ConstructionPower #MadeInJapan #PumpingPerformance #EngineeringInAction #TunnelConstruction #stronger4longer
Even under the most extreme and unpleasant conditions, Tsurumi pumps prove their strength and reliability time and again. Designed for challenging environments, our pumps continue to perform where others fail – whether in construction, tunneling, or wastewater applications.
Equipped with cutting wheels and shredding mechanisms, selected Tsurumi models are built to handle even the toughest materials. They ensure uninterrupted operation and outstanding durability, even in the harshest surroundings.
This Halloween season, we're celebrating the fearless spirit of Tsurumi – powerful, relentless, and always ready to take on the next challenge.
Because when the job gets dark and dirty, Tsurumi gets stronger.
#Stronger4Longer #Halloween #HappyHalloween #MonsterPump
At Tsurumi, the commitment to delivering exceptional pump quality "Made in Japan" is deeply rooted in every stage of development. To maintain and continuously prove this standard, all new pumps and prototypes undergo rigorous testing procedures before being released to the market.
Each model is examined in detail through comprehensive performance, motor, thermal, seal, and durability tests. These evaluations are carried out in advanced in-house facilities, including ventilation tanks, performance testers, and thermal testing systems.
To ensure objective verification, Tsurumi also works closely with independent experts from universities, research institutes, and certification bodies. This collaborative approach guarantees that every Tsurumi pump meets the highest technical and safety standards.
In addition to continuous internal testing, the company is investing further in its testing infrastructure to achieve both optimal pump performance and the required solids permeability for demanding applications. Thanks to state-of-the-art 3D printing technology, test-ready prototypes can now be produced in a very short time — significantly accelerating the development process.
With these efforts, Tsurumi reinforces its position as one of the global leaders in reliable and durable pumping solutions, ensuring that every product lives up to its promise: #Stronger4longer.
For more information or technical advice, please contact our team at: sales@tsurumi.eu
Tsurumi has taken another important step toward sustainability and climate protection by installing a large-scale photovoltaic (PV) system at its manufacturing facility in Kyoto, Japan.
The new solar installation consists of 1,430 modules with a total output of approximately 844 kW. It generates around 810,000 kWh of electricity per year, covering roughly 15.3% of the plant's annual energy requirements. By utilizing this clean energy, the factory will reduce its CO₂ emissions by over 340 tonnes annually.
A key feature of the system is its integrated battery storage unit, which provides backup power during outages and serves as an emergency power source.
With this investment, Tsurumi reinforces its commitment to sustainable manufacturing, energy efficiency, and environmental responsibility. The project is part of the company's broader initiative to minimize its ecological footprint and expand the use of renewable energy across all operations.
#Tsurumi #Sustainability #RenewableEnergy #SolarPower #GreenManufacturing #CleanEnergy #ClimateAction #EngineeringForTheFuture #PVSystem #Stronger4Longer
You can meet our French colleagues from Tsurumi France from Tuesday to Friday, 7-10 October, at a very important trade fair in Lyon: At Pollutec in Hall 6, Stand C090, an unusual programme awaits you: Every lunchtime, we invite you to an exclusive gastronomic event – a delicious break in the middle of the trade fair!
And every afternoon, you can experience pure action at the workshop on installing and removing #Tsurumi pumps. As a reward, you will receive an aperitif set!
In addition to culinary discoveries and technical challenges, the Tsurumi stand at #Pollutec is of course the place to find out about powerful pump models.
From Thursday to Saturday, 9–11 October, we look forward to welcoming you to the Tiefbau LIVE fair in Karlsruhe!
At stand F348 in area P3 of #TiefbauLIVE, Tsurumi will be showcasing a wide range of pumps in three areas:
- Powerful 230V pumps for civil engineering – ideal for dirty water, sludge and residual water on construction sites. Here, visitors can experience the LSC2.75 in wet live operation, among other things. Also on display are the LBA, HSA, HSD and NK series, as well as the robust 50 UTA2.75 for tough solid admixtures.
- Applications for buildings, basements and properties. Among other things, the super-compact Family series, a cutaway model of the POMA and the PNI will be on display here. A petrol-powered TEM-25H ensures self-sufficient operation, while our LSC flat suction pump with flange connection will be demonstrated in operation as a complete system.
- 400V pumps for demanding applications in infrastructure construction, building maintenance and special civil engineering. Tsurumi will be showcasing the powerful KTZ, KTVE and KTD. The technical highlight will be the powerful GPN3-80 agitator pump, presented as a sophisticated cutaway model – a real eye-catcher for anyone interested in technology.
Come to Lyon and Karlsruhe! We will bring you up to date on the latest developments in pumps for tough applications.
#stronger4longer
Exactly one year ago today, we at #Tsurumi reached another milestone in our 101-year history with the commissioning of our new motor factory in Kyoto: Covering an area of just over 13,000 square metres, we assemble motors for our high-performance submersible pumps with a wide power range from 0.4 to 350 kW and manufacture many motor components ourselves, such as our stator windings.
The use of state-of-the-art manufacturing technologies enables extremely high machining accuracy based on 3D CAD data. Our flexible manufacturing system and a high degree of automation using robot technology – for example in the manufacture of motor shafts and in intralogistics – ensure exceptional efficiency. At the same time, the new factory has also significantly expanded our capacity for testing and verifying the performance of our pumps.
We have invested a high double-digit million Euro amount in this project: an investment that is paying off because it allows us to optimally prepare for a sustainable future with low-emission, durable motors in premium quality 'Made in Japan' – to the benefit of our customers.
#stronger4longer
This coming Friday, September 26, at 11 a.m. (CEST), take about 30 minutes to join us for a new #Tsurumi online training session! Our technical experts will discuss the importance of pipe type and inner diameter in the design of submersible pumps.
Why is this so important for you? Because the choice of pipe type and internal diameter determines the efficiency and service life of submersible pumps. This is because they influence the hydraulic resistance and flow conditions.
Empirical data from practical experience shows that pipes with too small a diameter or made of unsuitable materials lead to increased pressure loss and, in extreme cases, to cavitation. The pump becomes overloaded, and its service life is shortened.
For example, a pipe that was too small (DN50 instead of DN80) in a sewage system doubled energy consumption and caused frequent failures due to overheating. Conversely, a correctly dimensioned pipe in a similar application reduced maintenance costs by 30% and extended the service life of the pump by two years.
In the live training session, we explain how to find the right pipes for your Tsurumi pump and the respective application. This is an important topic that you should not miss. We appreciate your interest! Use this link to join the free livestream on September 26:
https://us06web.zoom.us/webinar/register/4417387624970/WN_DSdQup5pQqyz6rqUIQFd5g
#stronger4longer
We are in the midst of man-made climate change. Summers are getting hotter worldwide, with long dry spells alternating with increasingly extreme rainfall events. In this world, it is important to take measures to slow down climate change. On the other hand, we must also adapt to the new reality. How do we deal with sudden heavy rainfall? When basements flood and sewers become overloaded?
Fire brigades, the construction industry and an increasing number of private users have been placing their trust in our #Tsurumi LSC flat suction pumps for many years. These are very compact, lightweight pumps that can be quickly transported to the site of operation with one hand – and start working immediately. Extremely easy to operate, the LSC pumps water down to a residual height of one millimetre. And anyone who has ever had to pump water out of a basement knows how long it takes to reach such a minimal water level.
In a short video, we show you how to start up the LSC and (rarely) maintain it: https://youtu.be/EpUYu4_vKjc?si=8meyKGAX1wXlwhl_
The specifications for the LSC series can be found on our website, of course: https://www.tsurumi.eu/products/drainage/lsc-56. We are happy to answer any questions you may have about our pumps and how to deal with heavy rainfall events. Write to us – we are here for you: sales@tsurumi.eu
#stronger4longer #climatechange #LSC #puddlesucker
Tsurumi pumps are ready for use straight from the factory and impress with their highly reliable and powerful performance from the moment the motor is started.
However, many of our customers naturally have special requests regarding the equipment of our pumps. Some want to convert the units for use in salty seawater. Others are looking for a way to install heavy pumps in a stable, free-standing position. Or they simply want to add a float switch.
We are happy to fulfil these and other requests with our range of accessories. You will find a wide selection on our website. These include:
- Various wear parts
- Pump outlets
- Flange adapters
- LSC suction adapters
- Electrode extensions
- Conversion kits for residues
- Electrode protection covers
- Oil leak sensors
- Seawater-resistant kits
- Float switches
- Motor protection plugs
- Kits for free-standing installation
- Guide rail mounting systems
- Cable repair kits
No more guessing what fits – we'll show you online. Click here and get the perfect combination: https://www.tsurumi.eu/products/accessories-575
Please take your time to browse and select the accessories you need. Of course, we are also happy to advise you personally. Simply send us an email and we will get back to you as soon as possible: sales@tsurumi.eu
#stronger4longer #accessories
Under the motto 'Practice meets technology', we welcome customers and interested parties from the construction industry, skilled trades and building services engineering to #Nordbau! IOn 10 September we will be kicking off at stand N260/270 at #Tsurumi: look forward to functional and cutaway models, the latest series and useful accessories.
On the one hand, everything revolves around classic construction applications with powerful 230V pumps for dirty water, sludge and residual water. Highlights include the flat suction pumps of the LSC series, the versatile LB, the powerful HSA, HSD and NK pumps, and the UTA for #wastewater with a high solids content. The presentation of our pump range is complemented by accessories and a clear model of the forced lubrication system developed in-house. Some of the pumps will be running live in wet conditions.
The focus is also on applications around the building: here we will be presenting, among other things, the super-small Family pumps, a cutaway model of the POMA, the PNI, a petrol-powered TEM and a residual water pump with flange connection – as a complete system.
We will also be showcasing 400V pumps for heavy-duty use in infrastructure construction, building maintenance and specialised civil engineering. Robust models from the KTZ and KTVE series, a powerful agitator pump and a compact stainless steel pump will be on display at the event.
Get up to speed on the latest developments in water logistics and visit us at Nordbau from 10 to 14 September! You can find out more about the trade fair here:
https://nordbau.de/de/
Visit our Finnish market partner Machinery Oy at #MAXPO, Finland's largest special exhibition for the construction industry!
From 28 to 30 August, you can discover #Tsurumi pumps at Hyvinkää Airfield at stand A143.
Anyone involved in construction projects in Scandinavia will discover the latest machinery and technologies at MAXPO. It goes without saying that Tsurumi contractor pumps will be there too. We look forward to seeing you there from Thursday onwards!
You can find more information about the trade fair on the MAXPO website: https://maxpo.messukeskus.com/en/
#stronger4longer
The so-called PID control (PID: proportional, integral, derivative) plays an important role in the legendary durability and energy efficiency of #Tsurumi pumps.
It offers users a major advantage in process control, as it continuously monitors the deviation between a desired setpoint and a process variable and adjusts the system's response as precisely as possible to the setpoint. In this way, the PID control in our pumps helps to save energy and extends service life.
We have recorded an online #training course on this topic. You can watch it in our #YouTube channel:
https://youtu.be/rI7xB_6ihW4?si=ALO4Lv2qL-SH4YHV
If you have any questions about PID control or other technical topics, please feel free to write to us – we will get back to you as soon as possible: sales@tsurumi.eu
In Italy, at our partner Dragflow we trained 12 experts and customers on #Tsurumi pumps over two days! The comprehensive programme included a large theoretical section and, of course, practical work on selected pumps!
First, we provided information on:
- our company
- the Tsurumi product portfolio with technical features
- differences in hydraulics
- applications in tunnel construction
- special applications such as booster/jetting
- our TRN submersible aerators
For the practical part, we randomly selected three rental pumps that had been returned shortly before. Therefore, we did not know what condition they would be in until we opened the pumps.
An LSC1.4S ran continuously for many years without maintenance, which is normal for Tsurumi pumps. Everything, including the motor, was in good condition; only the check valve and base plate had to be replaced.
An LH311W had been operating in salty seawater for two months. It was in good condition, only the sacrificial anodes in the strainer had to be replaced.
And in the case of a KRS822 after 12 months in salt water, the electrical parts were also in good condition. The hydraulic parts had to be replaced and serviced due to prolonged use in salt water.
The participants enjoyed dismantling and inspecting the pumps and carrying out the maintenance tasks. And we were happy to once again impart valuable knowledge about pumps!
Are you also interested in on-site training with our pump professionals? Then please send us an e-mail: sales@tsurumi.eu
We have once again added to the #FAQ here on our #Tsurumi #website. In addition to all the previous interesting topics, we now also answer these frequently asked questions:
- What type of threaded connection do Tsurumi pumps generally have on the pressure ports?
- Are pump models available with a PTC sensor?
- Are all types of stainless steel resistant to seawater?
- Which Tsurumi pumps are made entirely of stainless steel? Where are they mainly used?
- Why do bearings in pumps break?
Take a look right now. You are sure to find answers about our pumps that interest you:
https://www.tsurumi.eu/support/faq-418
#stronger4longer
Our online training on the Star Delta cabling of our pumps with many valuable tips and hints was very worthwhile for all participants. You can now watch the entire #Tsurumi training in the video:
https://youtu.be/-20dK1WdCUE
Have fun!
#stronger4longer #howto #howtovideo #onlinetraining
#Tsurumi pumps can be operated automatically in two ways: Via activation by a float switch or via an electrode.
Float switch
Float switches are often used where the performance of a pump is to depend on the water level. The switch is located in a piston that floats on the surface of the water. When the water level rises or falls, the float moves into position and opens or closes an internal switch that controls the pump's output.
Electrode
An electrode sensor recognises water based on its conductivity. It activates the pump when it is submerged under water. Unlike float switches, electrode sensors do not rely on mechanical movements. Instead, they utilise the natural conductivity of water to trigger an electrical reaction. Electrode sensors are permanently mounted directly on the pump. Ideal for installations where space is limited or a float mechanism could be blocked.
#stronger4longer
Finally, there is another #Tsurumi online training in English language! On Friday, 4 July at 11 a.m. (CEST), the technical experts from our Tsurumi's European headquarters will present the Star Delta connection of our pumps in a livestream. Our customers keep asking us about it. They want to understand what makes this connection so special. And we will explain it on Friday! We will show the Star Delta cabling using suitable pumps and point out possible sources of error in the connection.
At the end of the online training full of valuable know-how, you will, as always, be smarter than before!
Thank you for your interest! Follow this link to watch the free live stream on 4 July: https://us06web.zoom.us/webinar/register/7617387622704/WN_jmxcNqo7QS6FLL1QkUNVNw
#stronger4longer #onlinetraining #stardelta
From Sunday to Tuesday you can experience #Tsurumi pumps live at @Demopark 2025! This is Europe's largest open-air exhibition for the green construction industry! At the Eisenach-Kindel airfield in Hörselberg near Eisenach, construction machinery manufacturers will be showcasing their equipment and ideas for environmentally friendly and nature-orientated work. In our trade fair luggage we have for you, among other things:
• our puddle suckers Family and LSC 'in action'
• HS2.4S with flat suction plate
• HS2.75S
• HS3.75SL
• LB480A
• POMA
• 50UT2.4S
Visit us at stand F-603 - we look forward to seeing you!
Find out more about the #Demopark here:
https://demopark.de/
#stronger4longer #demopark25
Recently, our colleagues at @Tsurumi USA, in collaboration with Zone Industries, supported the development of a new launch pad for space rockets with our high-performance power units.
When a rocket is launched, its engines emit large flames. To cool the rocket, protect the concrete launch pad and absorb the resulting sound energy, a spray system releases thousands of litres of water during the launch. Most of the water turns into vapour, while the rest has to be pumped out.
To avoid this problem of evaporation, a newly designed spray system nicknamed the 'Booster Bidet' has been developed. This system delivers a powerful jet of over 360,000 litres of water within eight seconds. The water is fed through pipes from tanks pressurised with nitrogen. Finally, #Tsurumi high-pressure pumps from the KRS and LH series discharge the overflow water from the flame trench. In this way, the site is quickly prepared for repeated start-up cycles.
With more frequent launches into space, Tsurumi's pumps will play a relevant role in keeping the infrastructure intact and the missions on schedule.
The specifications of the KRS and LH series can be found on our website, of course. If you are interested in these pumps, we will be happy to advise you - just contact us via e-mail: sales@tsurumi.eu
#stronger4longer
The #NAK agricultural and farming machinery exhibition in Mezőfalva/Hungary, which we have also announced on our website, has been cancelled! The trade fair, at which our Hungarian market partner #VERBIS also wanted to present #Tsurumi high-performance pumps, was actually scheduled to take place this Wednesday and Thursday (4/5 June). However, there are currently outbreaks of foot-and-mouth disease in the region. In order to minimise the risk, the National Chamber of Agriculture (NAK) and the National Association of Dealers in Agricultural Equipment and Machinery have decided to cancel the fair.
If you are interested, you can of course experience Tsurumi pumps live not only at trade fairs, but also with our market partners and us: https://www.tsurumi.eu/about-tsurumi/distribution-network-15. Feel free to contact the experts on site - in Hungary, for example, our colleagues from VERBIS: https://www.verbis.hu/
Field trip on #FathersDay or film afternoon at home? 2,130 subscribers have made up their minds: they regularly visit the #Tsurumi #YouTube channel! Here you will find a wide variety of product, technical and construction site videos as well as online training. 209 videos are available to you. Some clips, such as this one on the FSP surface vacuum cleaner, are already 8 years old and therefore real classics. Above all, however, they are worth watching and helpful for all those who work with professional Tsurumi high-performance pumps 'Made in Japan'. Have fun browsing: https://youtu.be/BZLO0oD4wNA?si=KKryr_Mp7cg97OXa
#stronger4longer
Today and tomorrow, the key players in the #water industry are meeting in Bordeaux at Cycl'eau. Among the 150 exhibitors is #Tsurumi. Our colleagues from Tsurumi France look forward to seeing you at stand H3! Discover our range of industrial, construction, submersible and sewage pumps for all cases where water needs to be removed.
Find out more about the #Cycleau:
https://www.cycleau.fr/
#stronger4longer
The inrush current is generally limited during the soft start of a motor. Among other things, this prevents a voltage dip under heavy loads. At the same time, the mechanical components in the device are protected from excessive acceleration.
For these reasons, we use soft starters in our #Tsurumi pumps - whenever the direct start or the star/delta start are not suitable.
In a training video, we show how we use them to extend the service life of our pumps. You will learn more about:
- the operating principle of the soft starter,
- the connection diagram,
- various applications and
- experiences with different start ampere values.
Enjoy the video on our #YouTube channel:
https://youtu.be/P5SIum0NPPk?si=Sm6RRzgZZhhI31CE
#stronger4longer
Time is of the essence on the construction site of the future underground railway in #Toulouse, France. There is no time to chase numbers - especially when it comes to the quantities of #water to be pumped, the performance or the traceability required by the authorities. #Tsurumi Connect helps with all these issues:
Our digital system collects real-time data from the connected pumps, checks the direction of rotation and phase, monitors operating costs, enables preventive maintenance of the pumps and issues push notifications in the event of problems so that a quick response can be made.
Our colleagues from Tsurumi France installed the system on the large construction site and coupled it with a flow meter. The result: a reduced operational load, better responsiveness and more transparency for the teams on site and the site managers.
Details about Tsurumi Connect can be found here: https://www.tsurumi-connect.eu/
If you are interested in our digital system, we will be happy to advise you: sales@tsurumi.eu
#stronger4longer #tunnelling
This Friday and Saturday you can experience #Tsurumi high-performance pumps in Finland at Mansen Mörinät! Organised in the Tampere, Pirkkala and Lempäälä region, the event attracts more than 15,000 heavy machinery and transport equipment professionals every year. Our Finnish market partner Machinery Oy will have a whole range of contractor and #sewage pumps on the stand. Just drop by, we look forward to seeing you!
By the way: Machinery Oy is the first port of call for equipping construction projects with powerful Tsurumi pumps in Finland. You can find the experts using the location map in the attached photo.
#stronger4longer #mansenmorinat #machineryoy
Did you miss #BAUMA2025 in Munich? Too bad, because then you also missed the #Tsurumi highlights that we presented in Munich this year. These mainly included our contractor, wastewater and sewage pumps, but also a lot more - such as a smart booster installation with pumps connected in series, which we used to show how you can digitally network analogue pumps with Tsurumi Connect. This allows you to control, monitor and analyse your pumps or other connected machines.
To give you an impression of the trade fair, our video summarises seven exciting days at the fair in 80 seconds:
https://youtu.be/3BLHU9zyJJ4
#stronger4longer #bauma #bauma25 #wastewater #sewage
Our stand has been dismantled, our contractor and #wastewater pumps are on their way back to our warehouse at the #Tsurumi European headquarters in Düsseldorf. What remains are the memories of a very good week at #BAUMA and numerous interesting conversations with our trade fair guests!
Our Tsurumi team, supported by many of our European market partners, spent seven intensive days experiencing how important high-performance, durable and reliable pumps are to many companies in the construction industry. We were able to explain the quality and advantages of Tsurumi pumps in many discussions. We also learnt time and again from customers how well they can work with our solutions. This also includes our digital analysis, monitoring and control system Tsurumi Connect.
We are already looking forward to the next #bauma and the many other trade fairs where you can experience Tsurumi live in the meantime. But for now, we would like to thank you for your visit - see you next time!
#stronger4longer #BAUMA2025 #BAUMA25
Are you already looking forward to #BAUMA in Munich? This world trade fair for the construction industry only takes place every 3 years. As of today, the time has come again, and of course #Tsurumi is there.
We will be showing a large selection of contractor, #wastewater and sewage pumps at our stand A6.338 - and more: using the example of a smart booster installation with pumps connected in series, we will show you how you can digitally network analogue pumps: with Tsurumi Connect. This allows you to control, monitor and analyse your pumps or other connected machines. Furthermore you can experience for example the #Tsurumi CZ - our most powerful #sewage pump - at our booth. It has a special cutting configuration to prevent hard and fibrous solids from causing blockages. We will also be exhibiting TRN submersible aerators and MMS agitators for the wastewater sector at #BAUMA - and of course our compact wonders, the LSC flat puddle suckers. These remove #water down to a residual moisture content of one millimetre. In addition, despite their power, the LSC units are real lightweights so that they can be carried quickly to any job site.
Our place of operation from 7 to 13 April is #BAUMA2025 - hopefully yours too: We will welcome you to stand A6.338 with a Japanese ambience including a cosy bar and our tatami lounge. We look forward to your visit!
#stronger4longer #BAUMA25
When the rade fair BAUMA starts next Monday in Munich, it's worth visiting our stand A6.338 just to see #Tsurumi Connect. This is our digital system that allows you to network, control, monitor and analyse the parameters of analogue pumps and other construction machinery.
A fascinating innovation that our technology experts will be presenting to you at #BAUMA25 - and in advance in a video on our #YouTube channel. In the video, we use a few examples to demonstrate how to connect the Tsurumi Connect Box to a pump and sensors. The Tsurumi Connect Cloud is also a topic: https://youtu.be/Q3tDiVZJz0c?si=jqVJuzQrjWa5W6VB
Enjoy the film. If you have any questions about our digital solution or want to know how to use it optimally for your construction project, please contact us - either at BAUMA in Hall A6 or by email at sales@tsurumi.eu. You can also find more information online: www.tsurumi-connect.eu
#stronger4longer #bauma #bauma2025
Attention #Tsurumi fans and friends of excellent pumps! From now on you can also show the outside world which high-performance pumps your heart beats for. Discover great products online in our brand new fan shop that express your love for #stronger4longer: Jackets, shirts, caps and accessories like a cool #Stanley mug! Take a look right now - you're sure to find the ideal fan accessory for you in the Tsurumi fan shop:
https://zwineh-tw.myshopify.com
#stronger4longer
What an anniversary: Our chief technician Stefan Himmelsbach has now been working at #Tsurumi Europe for 25 years!
Stefan, we would like to congratulate you on this milestone and thank you very much for your support and tireless efforts! Thanks to your wealth of knowledge and experience in everything to do with professional pumps, we at Tsurumi have always been able to develop solutions for our customers' projects where others had previously failed. You have passed on your expertise in hundreds of training courses and workshops - our partners and we have learnt a lot from you! Not just about the KTZ, even though this model series was your favourite and you are considered as the "#KTZKing" at Tsurumi ...
Over the years, you have contributed so immensely to our success, but beyond that, you were and are above all a wonderful colleague and friend to us.
We are grateful for your loyalty and for enriching our company.
We look forward to many more successful years with you!
#stronger4longer
We would like to welcome a new member of our #Tsurumi KRS family: the KRS811! With an output of 11 kW and a discharge bore of 200 mm, it offers a maximum delivery rate of 5500 l/min and a maximum delivery head of 17.5 metres. The KRS811 joins the group of KRS pumps with its 4-pole motor with low speed - for even better durability on the construction site under harsh conditions. The design with top outlet and side discharge ensures efficient motor cooling even at low water levels.
Details on the KRS series and the new model can be found on our website - just click here. Interested? Then simply get in touch with us - we will be happy to advise you: sales@tsurumi.eu
#stronger4longer
We are looking forward to seeing you at #SMAGUA from 4-6 March in Zaragoza, Spain!
The 50th edition of the trade fair for #wastewater treatment is a must-attend event for #Tsurumi. Because we have suitable pumps in our portfolio for all tasks in this application area: At stand B9-13 in pavilion 4, the models 100CZ45.5, 22-BER, Skimmer 4-FSP and the TRN series will be presented in particular.
The MDQ sludge dryer and solids separation will also be on site. Let us explain the use and benefits to you!
Secure your free ticket for the trade fair now, simply by using the QR code in the image!
Discover another giant in the #Tsurumi family: The GSZ10150 is the largest model in the GSZ series. With a motor output of 150 kW, it achieves a maximum capacity of a truly gigantic 18,000 l/min and a delivery head of 54.5 m. These impressive performance values are particularly in demand in #mining and #tunnelling, where very large quantities of water have to be moved as quickly as possible over a relatively high delivery head.
In addition to the cooling jacket, with which every #GSZ model is equipped, the GSZ10150 has a cooling pipe. This ensures highly efficient motor cooling even in applications with a low water level.
Want to know more? Please feel free to contact us - we will be happy to provide you with information: sales@tsurumi.eu
#stronger4longer
Discover our #Tsurumi LH12185D! This version of the LH series has a special impeller and currently the largest motor in our contractor pump range: the 2-pole, 185 kW motor impresses with effortless power delivery for tough #dewatering work in #mining and other construction projects.
The LH12185D offers a maximum flow rate of 14000 l/min and a maximum delivery head of 85 m - ideal for mining and #tunnelling work. The special feature: The LH12185D can suck in large quantities of water from both the upper and lower side of the double suction impeller. This reduces the thrust load, which extends the service life of the bearings and increases the stability of the pump operation. To withstand the tough operating conditions, the impeller is made of wear-resistant, high-chromium cast iron.
Details on the LH series can be found on this website: https://www.tsurumi.eu/products/drainage/lh-161
If you are interested, we will be happy to advise you: sales@tsurumi.eu
#stronger4longer
A technological highlight in over 100 years of #Tsurumi history is the development of the oil lifter in 1998, which is partly responsible for the legendary reliability and reliability of our units. Our engineers in Japan invented this component, which is positioned around the mechanical seal and ensures optimum lubrication of the upper seal faces. This works even if the lubricant is reduced to up to 1/3 of the nominal volume.
Pumps without oil lifters displace the lubricating oil to the outside. This quickly leads to bearing damage. In all Tsurumi pumps, the oil lifter ensures that the mechanical seals are permanently lubricated. This extends the service life of the mechanical seal. In addition, the combination of double inner mechanical seal and oil lifter prevents seal damage during dry running. Since then, even when a Tsurumi is aligned horizontally, the seal faces remain lubricated, which contributes to the longevity of the pump and ensures maximum performance when working in any position.
This video shows what makes the Tsurumi oil lifter so unique:
https://www.youtube.com/watch?v=wZ0Une6_MVc
#stronger4longer
May we introduce? The powerful and robust #Tsurumi NKZ45.5 and NKZ611! The NKZ are sand and sludge pumps made of cast iron and driven by a 4-pole motor. The agitator mounted under the impeller supports the smooth pumping of water with settled solids. The spiral-shaped pump housing ensures the smooth passage of foreign matter in the medium.
The Tsurumi NKZ45.5 with 5.5 kW motor power offers you a maximum output of 2000 l/min and a maximum delivery head of 18.7 metres. The Tsurumi NKZ611 has even more power in store: with twice the motor power of 11kW, it pumps an impressive flow rate of up to 3,950 l/min over a maximum delivery head of 21.7m - that's about as high as a six-storey residential building.
The specifications of the NKZ series can be found here on our website:
https://www.tsurumi.eu/products/sand-and-slurry/nkz-179
At #Tsurumi, we attach great importance to products that enable our customers to pump even difficult-to-handle liquids. These include corrosive liquids, liquids at high temperatures and seawater.
A very special series for this is the Tsurumi LH-14 / LH-W-14 series made of stainless steel! It is now finally available from stock for customers in Europe.
The LH-14, like the LH-W-14 equipped with two impellers, is highly corrosion-resistant. All parts that come into contact with the medium are made of 316 stainless steel so that they can withstand extreme applications in the construction industry and in #mining.
The stainless steel LH is so tough that it would probably inspire respect even from famous fighting robots universe!
The specifications of the LH series can be found here on our website:
https://www.tsurumi.eu/products/drainage/lh-stainless-steel-475
If you are interested, we will be happy to advise you: sales@tsurumi.eu
#stronger4longer
Pumping #wastewater that contains contaminants with fibrous substances? Where conventional pumps fail, the #Tsurumi CZ series is in its element: The submersible pumps have a cutting and shredding function in a unique design: A heart-shaped suction opening with a sharp-edged fixed cutting blade combined with a semi-open channel impeller, which is also equipped with two sharp-edged blades, results in a scissor-like shredding mechanism.
This innovation enhances the CZ pump's ability to deal with larger debris. Clogging of the pump is thus prevented by a mix of shredding and crushing.
Attention! These models are now available from stock in Europe:
100CZ45.5 (5.5 kW), 100CZ47.5 (7.5 kW), 100CZ411 (11 kW) and 100CZ415 (15 kW)
The CZ series is presented here in the video:
https://youtu.be/pMMf_5wIkJI?si=g1YuIRTo1p6an0Yb
The specifications of the series can be found via the link in the comment below this post. If you are interested, we will be happy to advise you: sales@tsurumi.eu
#stronger4longer
Damaged cables are one of the main causes of pump failures. This is because capillary action can cause water to penetrate the cables, leading to insulation breakdowns, short circuits and costly repairs.
We at #Tsurumi have something to prevent this: our innovative anti-wicking cable entry system! This means that moisture can no longer penetrate, even with damaged cables. You benefit from minimal maintenance and maximum efficiency.
To see how the anti-wicking system is designed and how it works watch this video:
https://youtu.be/lnq_YORwVBw
Visit #Tsurumi at BAU 2025 in Munich! From January 13-17, we will be showcasing our entire portfolio of single-phase #wastewater pumps at stand C6.505. They can be easily operated with household electricity. You can experience some models live in wet operation at the trade fair. And best of all, you can also hire all these pumps in several European markets.
It's best to make a note of the date. Please feel free to stop by our stand. We look forward to many visitors and interesting discussions!
We're thrilled to announce the launch of our brand-new website: https://www.tsurumi-connect.eu/ ! Dive into the world of cutting-edge IoT solutions for pumps and discover how you can take full control of your pumping systems like never before.
Explore all the details and join us on this innovative journey. Your pumps, your control, our technology. Let's make a splash together!
#TsurumiConnect #IoTSolutions #PumpControl #Innovation #TechRevolution
We've just added a ton of new content to the user guide section on our website!
Now you can find a comprehensive impeller puller list, detailed overhaul manuals, and so much more. Whether you're looking to maintain your equipment or just want to learn more about our products, we've got you covered.
Check it out and make the most of our enhanced resources to keep your operations running smoothly!
#Innovation #WaterManagement #Pumps #Engineering #UserGuides #TsurumiEurope #NewContent #MaintenanceMadeEasy
Exciting News!
We are thrilled to announce the launch of new features on our website! You can now access full technical datasheets directly from our site, which were previously only available on Spaix.
But that's not all! Our innovative Pumpfinder tool now displays the specified duty point on the datasheets when you download them. This makes it easier than ever to find the perfect pump for your needs!
Visit our website today to explore these new features and enhance your experience with us. #Innovation #TechUpdate #Pumpfinder #EngineeringExcellence
We had an amazing time at the recent October Tsurumi technical training for our business partners! The sessions were not only informative but also incredibly fun. Our partners learned a lot and enjoyed every moment of the training. A big thank you to everyone who participated and made this event a success! #TsurumiTraining #LearningAndFun #BusinessPartners #TsurumiEurope
The process water of a plastic recycling plant naturally has a high proportion of plastics. This water must be collected and pumped by suitable pumps. Conventional shredding pumps repeatedly failed to perform this task. The solution for the customer was to switch to the hashtag#Tsurumi C series - one of the most reliable series in the market.
The 80C21.5 were able to pump the medium without any problems. A total of eight cutter pumps were installed in different basins to gradually remove the solids from the water so that it can be fed back into the recycling process.
All pumps are controlled by level sensors that keep the water in all containers at the same level, regardless of changes in the water inflow. By keeping the water level low, the pumps can collect more of the light solids that tend to accumulate on the water surface.
We have linked the specifications of the C series for you in the comment below this post.
hashtag#stronger4longer
If you've ever visited us at a trade fair, you'll be familiar with our hashtag#Tsurumi beer pump! An ingenious design that would certainly go down very well at your next barbecue party or any other celebration. We are now giving away three pumps, that will continue their second lives as beer pumps! Take part and get the chance to win one of these clever and cool "tapping systems"!
What do you have to do?
Tell us in a few sentences in which project in Europe you have used Tsurumi pumps. What was the challenge in the project? And how were you able to overcome it with Tsurumi? Which pump model did you use? Please send at least one picture or video of the project showing the Tsurumi pump used.
Please send your short project report to tsurumi@kommunikationskonsortium.com by midnight (CEST) on October 15 at the latest.
We will raffle off three beer pumps among all entries!
The winner will be announced here on LinkedIn and informed in writing. We look forward to your participation and many exciting Tsurumi projects! We wish everyone who takes part the best of luck in the prize draw.
Conditions of participation:
Anyone over the age of 18 and whose first place of residence is in Europe is eligible to take part. If there is more than one entry, the winner will be drawn by lot. Personal data (first and last name, postal address) will only be collected for the purposes of the competition and will be deleted afterwards. Payment of the equivalent value of the non-cash prize is not possible. By submitting photos/videos, participants automatically confirm that these are free of third-party rights and may be published free of charge by Tsurumi Europe GmbH and its affiliated companies. In addition, by participating in the competition, participants agree that Tsurumi Europe GmbH and its affiliated companies may use and publish their submissions (images and text information) for their own communication (website, social media, press work, brochures, ... and more). The closing date for entries is October 15, midnight (CEST). Participation in the competition constitutes acceptance of these terms and conditions. Legal recourse is excluded.
#stronger4longer
We are very much looking forward to IFAT 2024, which starts on Monday, May 13 in Munich! The "World's Leading Trade Fair for Water, Sewage, Waste and Raw Materials Management" will run until May 17, and we will of course be there again with many exciting products!
At our stand 444 in hall B1, the focus will be on our innovation Tsurumi CZ, which is now also available in Europe: a submersible motor pump with cutting and shredding function, specially designed for pumping wastewater containing solids.
We will also show these versatile solutions:
- MMR submersible mixer: a 4kW unit with gearbox for a powerful mixing effect with a propeller thrust of 1165N
- Pump station "TSURUBOX", for example for domestic waste water that is collected and pumped into the sewer. The pumping station is equipped with a Tsurumi Cutter pump for blockage-free operation.
- Tsurumi Connect: We show you how you can control the pump digitally - for example, to clear a blockage that has occurred.
- LSC1.4S: We will be demonstrating on the stand how this residual water pump extracts water down to a water level of just 1 mm.
- 32TRN21.5 Submersible aerator
- POMA vortex pump with fiber-reinforced plastic housing and float
- 50UT2.75S Vortex sewage pump with wide passage
- 50SQ2-2.75 made of stainless steel
- 50GY21.1S macerator pump with high delivery head up to more than 60 m.
Of course, we are also dedicating our appearance to the 100th anniversary of Tsurumi. How? Let us surprise you and come and visit us at the Messe München!
#stronger4longer
Lillestrøm or Paris?
Until Saturday, 27 April 2024, you have the great opportunity to experience Tsurumi high-performance pumps for the construction industry live at two important trade fairs. Either at the "Vei og Anlegg" in Lillestrøm, Norway, where our market partner Intec Pumper AS will be showing our contractor pumps in hall D01-07, or at the "Intermat" construction trade fair in Paris-Nord Villepinte, where our colleagues from Tsurumi France i will be demonstrating our units for civil engineering and tunnelling in hall 6 on stand A144. No matter which trade fair is closer to you - we are really looking forward to your visit and talking to you!
#stronger4longer
From Austria and Slovenia to Finland, from Italy to Norway: In April, you can experience #Tsurumi live at the following five trade fairs in Europe:
April 10-13
Mawev Show, St. Pölten, Austria
April 12-13:
Mansen Mörinät, Tampere, Finland
April 18-20:
GIC, Piacenza, Italy
April 24-27
Vei og Anlegg, Lillestrøm, Norway
April 17-19
Megra, Gornja Radgona, Slovenia
Find the event closest to you. We look forward to your visit!
You never stop learning. Of course, this also applies to the handling of our high-performance pumps and the pump technology behind them. That's why regular training and courses are a natural part of our service offering. This is why, dealers and partners from Belgium, Finland, Poland and France met last week for a training day at #Tsurumi in Düsseldorf! The topics: Pump selection, dismantling, electrical know-how and more. We also enjoyed delicious Japanese food - a first for some!
A first big order of Tsurumi Connect boxes had been programmed and configured for delivery in Norway. The designed system will provide maximum control of Tsurumi branded pumps as well as third manufacturer products. Together with Intec the Tsurumi Connect Team is solving the customer´s problem! Tsurumi Connect lets you digitize nearly all devices at your operation on site!
At the start of the construction work of our innovative #Tsurumi plant in #Kyoto, all those involved now met to pray in a Japanese ceremony for the work to proceed safely. We are very much looking forward to completion in September 2024.
#stronger4longer
Several #Tsurumi pumps of different series were installed in the wastewater treatment plant of a large Spanish hotel. The pumps perform important tasks at the main stations of the treatment process there.
Following units were installed:
TRN - self-priming submersible aerators for #wastewater treatment.
FSP - wastewater pumps with floats for use at the water surface
Two 80TRN47.5 operate in the biological reactor, and additional TRN submersible aerators are installed in the aerobic sludge digester and primary degreaser. At the surface of the decanter and sludge digester, two 4-FSP2s ensure the removal of wastewater containing solids.
We have linked the specifications of the two series for you in the comments below this post.
#stronger4longer